Difference between revisions of "End Device AT Commands and Downlink Commands"

From Wiki for Dragino Project
Jump to: navigation, search
(→‎0x23 Application Port)
(→‎Common Downlink Commands)
Line 126: Line 126:
 
* Downlink Payload: <span CLASS=bluetext>0x2500</span>, Set AT+DWELLT=0 to uplink.
 
* Downlink Payload: <span CLASS=bluetext>0x2500</span>, Set AT+DWELLT=0 to uplink.
 
* Downlink Payload: <span CLASS=bluetext>0x2501</span>, Set AT+DWELLT=1 to uplink.
 
* Downlink Payload: <span CLASS=bluetext>0x2501</span>, Set AT+DWELLT=1 to uplink.
 +
<br>
 +
 +
== 0x21 Set response level==
 +
* Downlink Payload: <span CLASS=bluetext>0x2101</span>, Set AT+RPL=1 to uplink.//Receive an unconfirmed packet and reply with an empty packet to the server.
 +
* Downlink Payload: <span CLASS=bluetext>0x210101</span>, Set AT+RPL=1,1 to uplink.//Receive an unconfirmed packet and reply with 00 packet to the server.
 +
 +
* Downlink Payload: <span CLASS=bluetext>0x2102</span>, Set AT+RPL=2 to uplink.//Receive the confirmed packet and reply an empty packet to the server.
 +
* Downlink Payload: <span CLASS=bluetext>0x210201</span>, Set AT+RPL=2,1 to uplink.//Receive the confirmed packet and reply with 00 packet to the server.
 +
 +
* Downlink Payload: <span CLASS=bluetext>0x2103</span>, Set AT+RPL=3 to uplink.//Receive an ADR packet and reply with an empty packet to the server.
 +
* Downlink Payload: <span CLASS=bluetext>0x210301</span>, Set AT+RPL=3,1 to uplink.//Receive an ADR packet reply to 00 packet to the server.
 
<br>
 
<br>

Revision as of 02:05, 11 October 2020

Introduction

Dragino LoRaWAN End Node support two types of Downlink Commands:

  • Common Commands: They should be available for each sensor, such as change uplink interval, reset device.
  • Sensor Related Commands: Only for special sensor, such as control relay, poll RS485 device.

This page shows the common commands since Dragino LoRaWAN stack DR-LWS-005. Make sure the end node support stack higher than DR-LWS-005 before checking this page.

How to use downlink command

See Devices User Manual.



Support End Node and firmware version

Dragino STM32 base hardware Firmware / LoRaWAN stack list
Model Description Firmware Version ; Stack Version
LSN50-v1, LSN50-V2, Open Source Generic LoRaWAN Sensor Node LSN50 v1.6.0 <--> DR-LWS-003;

LSN50 v1.7.0 <--> DR-LWS-005;



Common Downlink Commands


0x01 Change Uplink Interval

Format: Command Code (0x01) followed by 3 bytes time value.

If the downlink payload=0100003C, it means set the END Node’s Transmit Interval to 0x00003C=60(S), while type code is 01.

  • Example 1: Downlink Payload: 0100001E // Set Transmit Interval (TDC) = 30 seconds
  • Example 2: Downlink Payload: 0100003C // Set Transmit Interval (TDC) = 60 seconds



0x04 Reboot End Node

Format: Command Code (0x04) followed by FF.

If the downlink payload=04FF, the end node will reboot.


0x05 Enable/Disable Data Confirm Mode

Set end node to use confirm mode or unconfirm mode to uplink payload.

  • Downlink Payload: 05000001, Set AT+CFM=1, use confirm mode to uplink.
  • Downlink Payload: 05000000, set AT+CFM=0, use unconfirm mode to uplink.


0x04 Factory Data Reset

Format: Command Code (0x04) followed by FE.

If the downlink payload=04FE, Reset Parameters to Factory Default, Keys Reserve.

0x20 LoRa® Network Join Mode-- ABP or OTAA

Set the Network Join Mode. (0: ABP, 1: OTAA)

  • Downlink Payload: 0x2000, Set AT+NJM=O, use ABP mode to uplink.
  • Downlink Payload: 0x2001, Set AT+NJM=1, use OTAA mode to uplink.


0x22 Adaptive Rate

Set the Adaptive Data Rate setting. (0: off, 1: on)

  • Downlink Payload: 0x2201, Set AT+ADR=1.
  • Downlink Payload: 0x2200FFFF, Set AT+ADR=0.


0x23 Application Port

Set the application port

  • Example1 : Downlink Payload: 0x2305 // Set AT+PORT=5 .
  • Example2 : Downlink Payload: 0x2317 // Set AT+PORT=23 .


0x24 Eight Channel Mode

Set eight channels mode,Only for US915,AU915,CN470

  • Example : Downlink Payload: 0x24 01 // Set AT+CHE=1 902.3 902.5 902.7 902.9 903.1 903.3 903.5 903.7 .


0x25 UplinkDwellTime

Set UplinkDwellTime

  • Downlink Payload: 0x2500, Set AT+DWELLT=0 to uplink.
  • Downlink Payload: 0x2501, Set AT+DWELLT=1 to uplink.


0x21 Set response level

  • Downlink Payload: 0x2101, Set AT+RPL=1 to uplink.//Receive an unconfirmed packet and reply with an empty packet to the server.
  • Downlink Payload: 0x210101, Set AT+RPL=1,1 to uplink.//Receive an unconfirmed packet and reply with 00 packet to the server.
  • Downlink Payload: 0x2102, Set AT+RPL=2 to uplink.//Receive the confirmed packet and reply an empty packet to the server.
  • Downlink Payload: 0x210201, Set AT+RPL=2,1 to uplink.//Receive the confirmed packet and reply with 00 packet to the server.
  • Downlink Payload: 0x2103, Set AT+RPL=3 to uplink.//Receive an ADR packet and reply with an empty packet to the server.
  • Downlink Payload: 0x210301, Set AT+RPL=3,1 to uplink.//Receive an ADR packet reply to 00 packet to the server.


Retrieved from "https://wiki1.dragino.com/index.php?title=End_Device_AT_Commands_and_Downlink_Commands&oldid=7170"